MODEL AQUAPHOR S1000 A
Maximum compensated hardness – 1,540 mg/l
Maximum iron concentration – 10 mg/l
Manganese concentration – 1 mg/l
Permanganate oxidisability – 11 mgO2/l
Minimum pH – 6
Water and ambient temperature min. and max. – 5°–38 °C
Water pressure min./max. – 1.4–7 bar
Maximum flow to drain during regeneration, 9.1 L/min**
Nominal/maximum capacity – 30/42 l/min (1.8/2.5 m3/h)
Pressure drop at 22.7 l/min flow – 1 bar***
Capacity in HE mode, kg salt/grams of hardness 1.1 / 670
Capacity in HC mode, kg salt/grams of hardness 3.0 / 1,406
Maximum capacity in AU mode, kg salt/grams of hardness 5.4 / 1,680
Regeneration – smart, volume-based
Power parameters – 12V AC; 50/60 Hz; 0.015 kWh
Plumbing connections – 1 inch male
Minimum drain pipe diameter – 16 mm, 5/8 in.
Resin tank size – 26.7 x 58.4 cm
Height – 79.5 cm
Footprint, 40.4 x 48.5 cm
Gross weight ~48 kg
Fine-mesh, chlorine-resistant resin – 28 l
The Aquaphor Model S1000 A water softener features fully automatic processor control and effectively removes hardness salts, iron and organic impurities (permanganate oxidisability). The systems use innovative dual-core valves that speed up regeneration. The efficient and durable softener tank contains ultra-compact fine-mesh, chlorine-resistant ion exchange resin.
Needs up to 30% less salt
The specially designed tank contains ultra-fine-mesh, densely packed chlorine-resistant ion exchange resin with beads half the size of those in classic softeners. The tank design extends contact time with water and improves salt efficiency.
3-in-1: water softening, iron and organic impurity (permanganate oxidisability) removal
With the same volume of ion exchange resin, the AQUAPHOR S1000 A provides a larger surface area in contact with water, with no channelling effect, and the small beads regenerate faster and more efficiently. As a result, high Fe concentrations (up to 10 ppm) and organic impurities (permanganate oxidisability up to 11 mgO2/L) are removed.
Up to 5 times less water for regeneration
In classic column systems, regenerating a softener – especially an iron removal system – uses a lot of water. The innovative, patented AQUAPHOR S1000A dual-core valves ensure long-term, flawless operation while using a minimum of water.
Thanks to the innovative tank and smaller ion exchange resin size, the AQUAPHOR S1000A is a more sustainable option than other household water softeners. This unit needs less water and less salt per cycle to achieve the same or better results.
Counter-current regeneration in a compressed bed ensures the most effective regeneration of the sorbent from accumulated contaminants. The patented mesh flow distributor spreads the treated water flow evenly throughout the sorbent volume.
ADVANTAGES
The innovative dual-cylinder head valve controls water inflow and outflow from the softener tank. It has fewer parts, shorter and wider fluid paths and a self-closing/self-pressurising mechanism.
Removal of high Fe concentrations (up to 10 ppm).
Very low salt consumption.
Fast IER regeneration.
Easy installation and setup.
Minimal maintenance requirements.
A flow distribution device developed and patented by AQUAPHOR®.
A durable valve mechanism whose components are subject to the lowest possible load, tested to minimal wear after more than 5,500 cycles (more than 14 years of daily filter regeneration) at a maximum working pressure of 7 bar.
Easy-to-dismantle design in which any part can be replaced if needed.
Thanks to the removable valve design, it can be replaced quickly if needed.
Controller with an advanced monitoring and regeneration system, large screen and user-friendly interface.
Non-volatile memory that saves all settings and filter status in a power cut
3 setting modes: economy mode, high-capacity mode and automatic salt dose adjustment based on water consumption.
Filtration through the patented flow distributor lets water flow through the entire sorbent volume.
Thanks to the 100 µm flow distributor mesh, fine Super Fine ion exchange resin can be used without the risk of it being washed out.
The gaps between the fine Super Fine resin beads are much smaller than in standard resins, increasing filtration and regeneration efficiency.
The sorbent bed is sandwiched between flow distributors, so regeneration is counter-current and very efficient, starting with the least contaminated sorbent;
FILTER DESIGN
1. Compact cabinet-type housing.
2. High-capacity fine sorbent ensures high capacity and complete removal of iron, manganese, hardness salts and organic impurities (permanganate oxidisability).
3. A patented, in-house developed valve ensures smooth filter operation throughout its service life.
4. Controller with a large, informative screen.
5. The patented mesh flow distributor spreads the purified water flow evenly throughout the sorbent volume.
6. Sliding lid for easy access to the salt tank and a compact filter.
7. Standard bypass valve.
8. Strong tank made of durable glass-filled plastic.

TECHNICAL DATA
– Removes iron, manganese, hardness salts and organic impurities (permanganate) at the same time.
– Reliable stainless steel fittings and drain hose included.
– Reliability and durability in a pressure range of 1.5 to 7 atm.
Water used per regeneration ~100 L
Salt used per regeneration ~3.0 kg
System service life – 10 years.
The system meets NSF/ANSI 44 requirements for specific performance characteristics verified and substantiated by test data.





